MT-610 AM is a range of polyester TGIC Free powder coatings designed for exterior exposure with good weather resistance from just one application with specific antimicrobial activity. The coatings sustain a longer lifespan and are available in a wide range of colors and finishes which allow your product to shine. Additionally,MT-610 AM uses antimicrobial technology to reduce the number of microbes such as bacteria and mold. Test results have proven a reduction of bacteria and mold up to 99.9%.
MT-610 AM offers not only beautiful aesthetics but also a performance to match. It is ideally suited to a broad range of outdoor applications including outdoor furniture, playground equipment, signs, fencing, vending machines and general metal finishing. Can also be used for indoor application if required.
| Kasagaran nga kantidad | |
| Uri sa Kemikal | Polyester – TGIC Free |
| Densidad | 1.2 – 1.9 g/cm³, depende sa kolor ug epekto |
| Girekomenda nga gibag-on sa pelikula | 60 – 90µm |
| Shelf sa kinabuhi | 24 months below 30 °C 12 months below 35 °C |
| Mga Kahimtang sa Pagtipig | Ubos sa uga, bugnaw (≤ 30°C) nga mga kondisyon (open boxes must be resealed) |
| Iskedyul sa pagtambal | 30-40 min sa 170°C 10-20 min sa 180°C 8-16 min sa 200°C (sa temperatura sa butang) |
Galvanised steel requires surface preparation by either multi-stage pretreatment using either zinc phosphate or chromate conversion or controlled sweep blasting. Depending on the type of galvanizing, degassing or use of anti-bubbling additives may be required – follow the procedural advice of the pretreatment supplier. Iron phosphate and particularly Zinc phosphating of ferrous metals improves corrosion resistance. Aluminium substrates may require a chromate conversion coating.
Powders can be applied by manual or automatic electrostatic spray equipment. A good protection is linked with the recommended film thickness. All powders can show small color differences from batch to batch, this is normal and unavoidable. Applicators and fabricators are advised to use a single batch for parts that will be assembled together. Differences are more likely with special effect powders. Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling. Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect. Products with different codes should not be mixed even if same colour and gloss. It is recommended that for consistent application and appearance product be fluidized during application.
Actual product performance will depend upon the circumstances under which the product is used. Testing has been determined under laboratory conditions using the following application properties and is for guidance only.
| Pre-treatment | Zinc Phosphate |
| Substrate | Polished steel |
| Iskedyul sa pagtambal | 10 min sa 200°C |
| Gibag-on sa pelikula | 60 – 70µm |
| Kasagaran nga kantidad | Pamaagi/standard | |
| pagpilit | Class 0 | ISO 2409 (2 mm Crosshatch) |
| Erichsen cupping | Paglabay sa 5 mm | ISO 1520 |
| pagka-flexible | Paglabay sa 5 mm | ISO 1519 |
| katig-a | Pass - walay penetration sa substrate | ISO 1518-1 (2000g) |
| Impact-ato | Pass 2.5 Joules reverse & direct (20 in lb) | ISO 6272-2 (d/r) |
For help with solutions customized to your business needs, contact Export Director now.
Export Director
With 20+ years of experience and We firmly believe that product quality is the basis of cooperation.
Send Inquiry
TEl
+86-21-6420 0566
