MT-100 is a series epoxy based powder coatings that exhibit excellent corrosion protection and chemical resistance when applied over a properly prepared metal substrate. MT-100 is designed for interior application only. MT-100 powders are available in gloss, satin, matt and texture finishes in a wide range of colors.
| Kasagaran nga kantidad | |
| Uri sa Kemikal | epoxy |
| Densidad | 1.2 – 1.9 g/cm³, depende sa kolor ug epekto |
| Girekomenda nga gibag-on sa pelikula | 60 – 90µm |
| Shelf sa kinabuhi | 12 bulan |
| Mga Kahimtang sa Pagtipig | Ubos sa uga, bugnaw (≤ 25°C) nga mga kondisyon (ang mga bukas nga kahon kinahanglang ma-resealed) |
| Iskedyul sa pagtambal | 15-20 min sa 180°C 9-12 min sa 190°C 5-7 min sa 200°C |
Ang mga sangkap sa aluminyo kinahanglan makadawat usa ka bug-os nga multi-stage nga chromate conversion coating o angay nga chrome-free nga pre-treatment o angay nga pre-anodising aron malimpyohan ug makondisyon ang substrate. Kinahanglang pangitaon ang detalyadong tambag gikan sa supplier sa pre-treatment. Ang iron phosphate ug labi na ang Zinc phosphating sa ferrous nga mga metal nagpauswag sa resistensya sa kaagnasan. Ang mga substrate sa aluminyo mahimong magkinahanglan usa ka chromate conversion coating.
Powders can be applied by manual or automatic electrostatic spray equipment. Applicators and fabricators are advised to use a single batch for parts that will be assembled together. Differences are more likely with special effect powders. Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling. Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect. Products with different codes should not be mixed even if same colour and gloss. It is recommended that for consistent application and appearance product be fluidized during application.
| Pamaagi sa Paggamit | Tribo, Electrostatic |
| pag-recycle | Unused powder can be reclaimed using suitable equipment and recycled through the coating system, but a minimum of 70% virgin powder should be used. |
Ang aktuwal nga pasundayag sa produkto magdepende sa mga kahimtang diin gigamit ang produkto. Ang mga resulta gibase sa mekanikal ug kemikal nga mga pagsulay nga (gawas kung gipahibalo) nga gihimo sa ilawom sa mga kondisyon sa laboratoryo ug gihatag alang sa paggiya lamang.
| Pre-treatment | Zinc Phosphate |
| Substrate | Pinasinaw nga asero |
| Iskedyul sa pagtambal | 5 min sa 200°C (temperatura sa butang) |
| Gibag-on sa pelikula | 60 – 70µm |
| Kasagaran nga kantidad | Pamaagi/standard | |
| pagpilit | Class 0 | ISO 2409 (2 mm Crosshatch) |
| Erichsen cupping | Paglabay sa 5 mm | ISO 1520 |
| pagka-flexible | Paglabay sa 5 mm | ISO 1519 |
| katig-a | Pass - walay penetration sa substrate | ISO 1518-1 (2000g) |
| Impact-ato | Ipasa ang 2.5 Joules nga balikbalik ug direkta (20 sa lb) | ISO 6272-2 (d/r) |
Whilst maintaining the general protective and anti-corrosive properties of powder coatings, aluminum and copper/bronze metallic finishes, when submitted to the listed tests, may rapidly show a loss of metallic aspect. The results shown are based on tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for advice only, actual performance depends upon the circumstances under which the product is used.
| Kasagaran nga kantidad | Pamaagi/standard | |
| Pagbatok sa Kemikal | Excellent resistance to acid, alkalis, oils and chemicals at room temperatures. | |
| Pagsulay sa asin nga spray | Pass, no corrosion creep more than 3 mm from scribe, 500 h | ISO 9227 |
| Kasagaran nga kantidad | Pamaagi/standard | |
| humidity | Pass – no blistering or loss of gloss, 1000 h | ISO 6270-2 CH (Padayon nga humidity) |
| Kalig-on sa gawas | Some chalking and loss of gloss after 3-6 months continuous outdoor exposure. Protective properties retained. Not recommended for outdoor applications. |
| Pagpangandam sa nawong | Damaged areas must be clean and free of grease or rust. Dry-sand the area with 600 grade paper down to the substrate. The area must be completely free of dust and cleaned with a non-aggressive solvent before proceeding. Any damage of the coating system must be repaired as soon as possible. |
| Paggamit | For repairs a PU (2K or 1K) liquid paint is recommended. |
For help with solutions customized to your business needs, contact Export Director now.
Export Director
With 20+ years of experience and We firmly believe that product quality is the basis of cooperation.
Send Inquiry
TEl
+86-21-6420 0566
